What does slow sand filter remove?
Rachel Newton
What does slow sand filter remove?
Slow sand filtration is a type of centralised or semi-centralised water purification system. A well-designed and properly maintained slow sand filter (SSF) effectively removes turbidity and pathogenic organisms through various biological, physical and chemical processes in a single treatment step.
Which is an important requirements for slow sand filters to function properly?
The key points and observations to make during a sanitary inspection of a slow sand filter are : The turbidity of the inlet water should be below 10 TU. The turbidity of the outlet water should be below 5 TU. The flow rate in the filter should be constant and in the range 0.1 to 0.3 metres per hour.
How often should a slow sand filter be cleaned?
A rapid sand filter is maintained and cleaned by forcefully injecting water backwards through the entire sand bed every 2 or 3 days. Backwashing a biological sand filter will destroy it and may result in people getting very sick if water from it is being consumed.
What is the thickness of bed in slow sand filter tank?
The filter bed is built to a depth of 1-1.5 m (or more) with a minimum of . 8m on smaller filters. This depth of sand will allow for losses which will occur if the top portion of the sand is removed when particulate matter and algae is cleaned from the top of the sand.
How much is the capacity of slow sand filter to remove the bacteria?
Slow sand filters can reduce water turbidity to less than 1 NTU, total organic content by 10%, remove 95% of coliform bacteria, improve a water’s color, taste, and odor, and do not result in significant sludge production.
What is the rate of filtration in slow sand filter?
In slow filtration, a fine sand is used, and the designed rate of downward flow of the water under treatment normally lies between 0.1 and 0.4 m3/h per square metre of surface. Unless the water to be treated is of exceptional turbidity, a filter of this type may run for weeks or even months without cleaning.
Which is the first zone of purification in a slow sand filter bed?
Schmutzdecke zone
Explanation: Schmutzdecke zone is the first zone of purification in a sand bed. It comes under the biological action of filtration.
What are three advantages of a slow sand filter?
The major advantages of slow sand filters are:
- Effective treatment for turbidity, bacteria, and greater than 4 log removal of cysts.
- No pre-treatment chemicals.
- No backwashing.
- No automation required.
- A failure to clean the filter will result in loss of production but no loss of quality.
What is the type of cleaning is done in rapid sand filters?
Rapid sand filters must be cleaned frequently, often several times a day, by backwashing, which involves reversing the direction of the water and adding compressed air. During backwashing, the bed is fluidized and care must be taken not to wash away the media.
What is the normal rate of filtration adopted for slow sand filter?
100 to 200 liters per hour
Note:
| Characteristics | Slow Sand Filters | Rapid Sand Filters |
|---|---|---|
| Rate of filtration | Low, typically ranges 100 to 200 liters per hour per sq. m of filter area. | High, typically ranges 3000 to 6000 liters per hour per sq. m of filter area. |
What is the effective size of sand particles used in slow sand filters?
Explanation:
| Slow sand filter | Rapid sand filter |
|---|---|
| Post-treatment optional | Post-treatment compulsory |
| Sand filter characteristics Grain size – 0.15 to 0.30 mm Coefficient of uniformity (grain) – 1.8 to 2.5 or 3. | Sand filter characteristics Grain size – 0.35 to 0.55 mm Coefficient of uniformity (grain)- 1.2 to 1.7 |
What is the rate of filtration for slow sand filter?
In slow filtration, a fine sand is used, and the designed rate of downward flow of the water under treatment normally lies between 0.1 and 0.4 m3/h per square metre of surface.
What is slow sand filtration?
Slow sand filtration refers to a process of water purification and filtration that uses sand and beneficial microorganisms.
Does slow sand water filter remove arsenic too?
) found that metal-coated sand has been shown to remove arsenic. Intermittent slow sand filters, when challenged with organic and inorganic toxicants at levels 10 – 100 times normal environmental levels, were found to be able to retain between 50 – 99% of toxicants.
How to make a sand filter?
Obtain the Materials for Your Filter. Purchase a 10-gallon,tall,rectangular,clear plastic storage container with a tight-fitting lid.
What is the flow rate of a sand filter?
Traditionally, flow rates in slow sand filters should be between 0.1 – 0.4 m/hour. Note that this is a compaction of m3/m2/hour and sometimes the unit is in days and not hours. For the concrete filter, this equates to a maximum of 22 to 25 litres per hour depending on if the filter is round or square.
